Simat Labs

People Counting

People Counting

Directional in and out counts and live occupancy at every entrance — anonymous, on-premise.

Flagship — Abdali Mall

--:--

LIVE·4 cams·anonymous · no identities

Today

1,284

In store

37

Avg dwell

1m 12s

Z1

Entrance

1,284 · dwell 14s

Z2

New arrivals

842 · dwell 1m 36s

Z3

Checkout

611 · dwell 2m 22s

Z4

Back wall

203 · dwell 38s

edge-store-01 · healthy

by hour

People Counting measures how many people enter and leave a space, through every door, gate, or corridor you point a camera at.
Directional counts add up to live occupancy, so teams know how full a store, floor, or venue is right now, and how traffic moves through the day and week.

Counting runs on-premise and is anonymous by design: people are counted as shapes crossing a line. No faces are stored and no one is identified.Counts and occupancy flow to the dashboard, and threshold alerts — a floor over capacity, an entrance suddenly busy — go out through no-code automations.

In and out at every entrance

Directional counts on virtual lines at each door, gate, or corridor, calibrated per entrance during the pilot.

Live occupancy

Entries minus exits, per floor, zone, or building, with alerts when a space passes the limit you set.

Traffic trends

Hourly, daily, and weekly traffic per entrance and site, ready to compare and export.

Powered by IFA

Runs as a module on the IFA edge box beside your cameras.

About IFA

The IFA dashboard

One dashboard for every module

Every IFA module reports into the same web dashboard. A new module shows up with its charts, events, and automations the day it is deployed — nothing is coded per module.

Plant overview — today

HourDayWeek·group by: line

Events per hour

Line 3 · QA failsDock 4 · crossings
020406006:0008:0010:0012:0014:0016:00Dock 4 · crossingsLine 3 · QA fails

Events by severity

Critical6
Warning41
Info137

184 events · 2 modules · 4 cameras

Streams

  • Line 3 — labeleronline · 24 fps · 41 ms
  • Dock 4 — closeonline · 20 fps · 38 ms
  • Dock 4 — fardegraded · 11 fps · 2 reconnects
  • Line 1 — capperoffline · last seen 09:12

Automation runs

  • Label fail → email shift leadok11:42
  • 5 fails in 10 min → capture + WhatsAppok11:38
  • Dock 4 far offline → emailsuppressed11:20
  • Session closed → reportok10:57

Live camera monitoring

Every camera as a health card: online, degraded, or offline, with frame rate, latency, and uptime, and a live view from the edge box when it is streaming. Refreshes on its own.

Charts derived from events

Pick a metric, group by line, zone, severity, or product, and bucket by hour, day, or week. Line, bar, area, stacked, and pie — all built from the events a module emits, never hand-coded.

Event log and notifications

Every event, filterable by module, type, and severity, with the frame that triggered it. Email and WhatsApp notifications go out through automations, with a per-run record of what was sent and what was suppressed.

No-code automations

A drag-and-connect flow builder: a trigger (a module event, a camera going offline, a schedule), logic (filter, window, cooldown, time gate), then actions — send an email, send a WhatsApp message, capture the frame, generate a report.

Reports for managers

A report action turns a session or a shift into a readable document — totals, shares, per-product detail — attached to the notification email and kept in the dashboard's report list.

People counting questions

Is anyone identified?

No. People are counted as shapes crossing a line. No faces are stored, no one is identified, and only counts and occupancy leave the site.

How accurate are the counts?

Accuracy depends on camera placement and height, so each entrance is checked against manual counts during the pilot before numbers go live. We report the measured accuracy per entrance rather than quoting one figure for every site.

What cameras do we need?

Existing overhead or angled CCTV with an RTSP/ONVIF stream usually works. Where an entrance has no usable view, a standard IP camera is added. Counting runs on the IFA edge box on site.

Can it alert us?

Yes. Occupancy and count thresholds can trigger email alerts or reports through no-code automations in the dashboard, with every alert logged.

Last updated: